Обновление и Wi-Fi

[Галахов Роман]

Вчера Wi-Fi работал хорошо. Обновил систему вечером. На ночь выключил ноутбук, утром включаю Wi-Fi не включается (NM - его не видит, только ethernet) Облазил все (пробовал из Gnome (чип Wi-Fi - bluetooth - и только Gnome видит bluetooth) - ничего не помогает. Думал чип сдох. Но когда загрузился с LiveUSB Fresh R1 х86-64 - там Wi-Fi работает. Загрузил основную - нет. Не понимаю.
Выводы из основной системы, где не работает WiFi:

Код: Выделить всё

Travelmate roman # uname -a
Linux Travelmate.kenetic 3.10.9-nrj-desktop-1rosa #1 SMP PREEMPT Tue Aug 27 19:36:40 MSK 2013 x86_64 x86_64 x86_64 GNU/Linux
Travelmate roman # cat /etc/release
ROSA Desktop Fresh R1 release 2012.1 for x86_64
Travelmate roman # lspci
00:00.0 Host bridge: Intel Corporation Core Processor DRAM Controller (rev 02)
00:02.0 VGA compatible controller: Intel Corporation Core Processor Integrated Graphics Controller (rev 02)
00:16.0 Communication controller: Intel Corporation 5 Series/3400 Series Chipset HECI Controller (rev 06)
00:1a.0 USB controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 05)
00:1b.0 Audio device: Intel Corporation 5 Series/3400 Series Chipset High Definition Audio (rev 05)
00:1c.0 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 1 (rev 05)
00:1c.1 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 2 (rev 05)
00:1c.2 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 3 (rev 05)
00:1d.0 USB controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 05)
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev a5)
00:1f.0 ISA bridge: Intel Corporation Mobile 5 Series Chipset LPC Interface Controller (rev 05)
00:1f.2 SATA controller: Intel Corporation 5 Series/3400 Series Chipset 4 port SATA AHCI Controller (rev 05)
00:1f.3 SMBus: Intel Corporation 5 Series/3400 Series Chipset SMBus Controller (rev 05)
00:1f.6 Signal processing controller: Intel Corporation 5 Series/3400 Series Chipset Thermal Subsystem (rev 05)
01:00.0 Network controller: Broadcom Corporation BCM43225 802.11b/g/n (rev 01)
03:00.0 Ethernet controller: Broadcom Corporation NetXtreme BCM57760 Gigabit Ethernet PCIe (rev 01)
ff:00.0 Host bridge: Intel Corporation Core Processor QuickPath Architecture Generic Non-core Registers (rev 05)
ff:00.1 Host bridge: Intel Corporation Core Processor QuickPath Architecture System Address Decoder (rev 05)
ff:02.0 Host bridge: Intel Corporation Core Processor QPI Link 0 (rev 05)
ff:02.1 Host bridge: Intel Corporation Core Processor QPI Physical 0 (rev 05)
ff:02.2 Host bridge: Intel Corporation Core Processor Reserved (rev 05)
ff:02.3 Host bridge: Intel Corporation Core Processor Reserved (rev 05)
Travelmate roman # lsmod
Module                  Size  Used by
hid_generic            12548  0 
usbhid                 52965  0 
hid                   100968  2 hid_generic,usbhid
af_packet              35603  2 
tun                    27139  0 
fuse                   87750  3 
bnep                   19701  2 
bluetooth             372322  7 bnep
vboxnetadp             25670  0 
vboxnetflt             27613  0 
vboxdrv               320380  2 vboxnetadp,vboxnetflt
uvcvideo               80968  0 
videobuf2_vmalloc      13216  1 uvcvideo
videobuf2_memops       13362  1 videobuf2_vmalloc
videobuf2_core         40543  1 uvcvideo
videodev              131178  2 uvcvideo,videobuf2_core
media                  21439  2 uvcvideo,videodev
dm_mirror              22085  0 
dm_region_hash         20849  1 dm_mirror
dm_log                 18529  2 dm_region_hash,dm_mirror
dm_mod                 88312  2 dm_log,dm_mirror
battery                13842  0 
ac                     13031  0 
brcmsmac              526358  0 
cordic                 12574  1 brcmsmac
brcmutil               15618  1 brcmsmac
b43                   418733  0 
mac80211              526842  2 b43,brcmsmac
cfg80211              490861  3 b43,brcmsmac,mac80211
acer_wmi               32547  0 
sparse_keymap          13890  1 acer_wmi
ssb                    67885  1 b43
mmc_core              120586  2 b43,ssb
rfkill                 22426  4 cfg80211,acer_wmi,bluetooth
rng_core               13395  1 b43
pcmcia                 61806  2 b43,ssb
pcmcia_core            23631  1 pcmcia
intel_powerclamp       18764  0 
iTCO_wdt               13480  0 
iTCO_vendor_support    13718  1 iTCO_wdt
evdev                  17757  15 
i2c_i801               22443  0 
coretemp               13435  0 
serio_raw              13413  0 
joydev                 17377  0 
broadcom               13170  0 
wmi                    19070  1 acer_wmi
acpi_cpufreq           19612  1 
mperf                  12667  1 acpi_cpufreq
tg3                   162360  0 
thermal                18435  0 
snd_hda_codec_conexant    56945  1 
fan                    13002  0 
ptp                    18580  1 tg3
pps_core               19057  1 ptp
libphy                 35218  2 tg3,broadcom
bcma                   46619  2 b43,brcmsmac
processor              40258  1 acpi_cpufreq
lpc_ich                16977  0 
snd_hda_intel          43820  2 
intel_ips              18421  0 
kvm_intel             138619  0 
snd_hda_codec         192591  2 snd_hda_codec_conexant,snd_hda_intel
kvm                   433425  1 kvm_intel
snd_hwdep              17698  1 snd_hda_codec
crc32c_intel           22079  0 
microcode              19401  0 
snd_pcm               101961  2 snd_hda_codec,snd_hda_intel
snd_page_alloc         18710  2 snd_pcm,snd_hda_intel
snd_timer              29370  1 snd_pcm
snd                    83251  10 snd_hwdep,snd_timer,snd_hda_codec_conexant,snd_pcm,snd_hda_codec,snd_hda_intel
soundcore              15047  1 snd
binfmt_misc            17431  1 
ipv6                  360287  46 
autofs4                38674  3 
sr_mod                 22411  0 
ehci_pci               12905  0 
ehci_hcd               61236  1 ehci_pci
usbcore               228202  4 uvcvideo,ehci_hcd,ehci_pci,usbhid
usb_common             13057  1 usbcore
i915                  624212  7 
video                  19216  2 i915,acer_wmi
button                 13871  1 i915
i2c_algo_bit           13413  1 i915
drm_kms_helper         44366  1 i915
drm                   294245  3 i915,drm_kms_helper
i2c_core               40536  6 drm,i915,i2c_i801,drm_kms_helper,i2c_algo_bit,videodev
Travelmate roman # lspcidrake
unknown         : Intel Corporation|Core Processor Reserved [BRIDGE_HOST] (rev: 05)
unknown         : Intel Corporation|Core Processor Reserved [BRIDGE_HOST] (rev: 05)
unknown         : Intel Corporation|Core Processor QPI Physical 0 [BRIDGE_HOST] (rev: 05)
unknown         : Intel Corporation|Core Processor QPI Link 0 [BRIDGE_HOST] (rev: 05)
unknown         : Intel Corporation|Core Processor QuickPath Architecture System Address Decoder [BRIDGE_HOST] (rev: 05)
unknown         : Intel Corporation|Core Processor QuickPath Architecture Generic Non-core Registers [BRIDGE_HOST] (rev: 05)
tg3             : Broadcom Corporation|NetXtreme BCM57760 Gigabit Ethernet PCIe [NETWORK_ETHERNET] (rev: 01)
bcma            : Broadcom Corporation|BCM43225 802.11b/g/n [NETWORK_OTHER] (rev: 01)
intel_ips       : Intel Corporation|5 Series/3400 Series Chipset Thermal Subsystem [SIGNAL_OTHER] (rev: 05)
i2c_i801        : Intel Corporation|5 Series/3400 Series Chipset SMBus Controller [SERIAL_SMBUS] (rev: 05)
ahci            : Intel Corporation|5 Series/3400 Series Chipset 4 port SATA AHCI Controller [STORAGE_SATA] (rev: 05)
lpc_ich         : Intel Corporation|Mobile 5 Series Chipset LPC Interface Controller [BRIDGE_ISA] (rev: 05)
unknown         : Intel Corporation|82801 Mobile PCI Bridge [BRIDGE_PCI] (rev: a5)
ehci_pci        : Intel Corporation|5 Series/3400 Series Chipset USB2 Enhanced Host Controller [SERIAL_USB] (rev: 05)
shpchp          : Intel Corporation|5 Series/3400 Series Chipset PCI Express Root Port 3 [BRIDGE_PCI] (rev: 05)
shpchp          : Intel Corporation|5 Series/3400 Series Chipset PCI Express Root Port 2 [BRIDGE_PCI] (rev: 05)
shpchp          : Intel Corporation|5 Series/3400 Series Chipset PCI Express Root Port 1 [BRIDGE_PCI] (rev: 05)
snd_hda_intel   : Intel Corporation|5 Series/3400 Series Chipset High Definition Audio [MULTIMEDIA_AUDIO_DEV] (rev: 05)
ehci_pci        : Intel Corporation|5 Series/3400 Series Chipset USB2 Enhanced Host Controller [SERIAL_USB] (rev: 05)
mei             : Intel Corporation|5 Series/3400 Series Chipset HECI Controller [COMMUNICATION_OTHER] (rev: 06)
i915            : Intel Corporation|Core Processor Integrated Graphics Controller [DISPLAY_VGA] (rev: 02)
unknown         : Intel Corporation|Core Processor DRAM Controller [BRIDGE_HOST] (rev: 02)
hub             : Linux 3.10.9-nrj-desktop-1rosa ehci_hcd|EHCI Host Controller [Hub|Unused|Full speed (or root) hub]
hub             : Intel Corp.|Integrated Rate Matching Hub [Hub|Unused|Full speed (or root) hub]
usbhid          : Trust International B.V.| USB OPTICAL MOUSE [Human Interface Device|Boot Interface Subclass|Mouse]
hub             : Linux 3.10.9-nrj-desktop-1rosa ehci_hcd|EHCI Host Controller [Hub|Unused|Full speed (or root) hub]
hub             : Intel Corp.|Integrated Rate Matching Hub [Hub|Unused|Full speed (or root) hub]
uvcvideo        : Suyin|1.3M WebCam [Video|Video Control]
unknown         : Generic|FingerPrinter Reader
Type:laptop     : Acer.*|TravelMate.*
hid_generic     :  USB OPTICAL MOUSE
Travelmate roman # 

Если нужно могу загрузиться в Live и дать выводы оттуда, и еще какие выводы нужны?
Ну хоть чем то меня система порадовала - наконец - то нашла сканер отпечатков пальцев:

[akdengi]

C системы где нету wifi нужны выводы:

ifconfig

dmesg | grep wlan0

[PastorDi]

Broadcom (у меня) wlan0 не показывает, он на eth1 сидит.

Можете просто установить urpmi dkms-broadcom-wl и должно все работать.

[euspectre]

Вывод dmesg всё же нужен.

[Галахов Роман]

C системы где нету wifi нужны выводы:

ifconfig

dmesg | grep wlan0

Сделал:

Код: Выделить всё

Travelmate roman # ifconfig
eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST>  mtu 1500
        inet 192.168.1.11  netmask 255.255.255.0  broadcast 192.168.1.255
        inet6 fe80::21e:33ff:fe29:29e5  prefixlen 64  scopeid 0x20<link>
        ether 00:1e:33:29:29:e5  txqueuelen 1000  (Ethernet)
        RX packets 2486  bytes 1932826 (1.8 MiB)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 2727  bytes 498992 (487.2 KiB)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0
        device interrupt 18  

lo: flags=73<UP,LOOPBACK,RUNNING>  mtu 65536
        inet 127.0.0.1  netmask 255.0.0.0
        inet6 ::1  prefixlen 128  scopeid 0x10<host>
        loop  txqueuelen 0  (Local Loopback)
        RX packets 8  bytes 400 (400.0 B)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 8  bytes 400 (400.0 B)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

Travelmate roman # 
Travelmate roman # dmesg | grep wlan0
Travelmate roman # 

[Галахов Роман]

Broadcom (у меня) wlan0 не показывает, он на eth1 сидит.

Можете просто установить urpmi dkms-broadcom-wl и должно все работать.

У вас, наверное, вручную настроено.
Когда отключен (программно) чип Wi-Fi да - у меня провод взял себе и eth0 и wlan0 и wwan0
Но когда Wi-Fi чип работает, то все нормально. Специально перезагружался в Live посмотреть.
Когда включен провод и отключен Wi-Fi

Код: Выделить всё

root@localhost live]# dmesg | grep wlan0
[   20.518203] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[root@localhost live]# 

Когда Wi-Fi работает (провод нет):

Код: Выделить всё

root@localhost live]# dmesg | grep wlan0
[   20.518203] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[  302.001230] wlan0: authenticate with cc:5d:4e:fb:31:b8
[  302.004416] wlan0: send auth to cc:5d:4e:fb:31:b8 (try 1/3)
[  302.005563] wlan0: authenticated
[  302.006418] wlan0: associate with cc:5d:4e:fb:31:b8 (try 1/3)
[  302.008815] wlan0: RX AssocResp from cc:5d:4e:fb:31:b8 (capab=0x411 status=0 aid=1)
[  302.009631] wlan0: associated
[  302.009686] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[  302.079708] wlan0: deauthenticating from cc:5d:4e:fb:31:b8 by local choice (reason=3)
[  303.027467] wlan0: authenticate with cc:5d:4e:fb:31:b8
[  303.028871] wlan0: send auth to cc:5d:4e:fb:31:b8 (try 1/3)
[  303.029918] wlan0: authenticated
[  303.030833] wlan0: associate with cc:5d:4e:fb:31:b8 (try 1/3)
[  303.033157] wlan0: RX AssocResp from cc:5d:4e:fb:31:b8 (capab=0x411 status=0 aid=1)
[  303.033803] wlan0: associated
[root@localhost live]# 

[Галахов Роман]

Можете просто установить urpmi dkms-broadcom-wl и должно все работать.

Спасибо! Помогло. Теперь буду знать. Интересно, почему раньше без него работало, а после вчерашнего обновления нет.
И, наверное, не я один не знал, что нужно устанавливать этот пакет.

[PastorDi]

Можете просто установить urpmi dkms-broadcom-wl и должно все работать.

Спасибо! Помогло. Теперь буду знать. Интересно, почему раньше без него работало, а после вчерашнего обновления нет.
И, наверное, не я один не знал, что нужно устанавливать этот пакет.

Ну какбы у нас у Broadcom'ов всего 2 драйвера:
1. b43-firmware-install
2. dkms-broadcom-wl

Так что... любой можно использовать, главное чтобы понять какой лучше работает, на том и остановиться.

[Галахов Роман]

Ну какбы у нас у Broadcom'ов всего 2 драйвера:
1. b43-firmware-install
2. dkms-broadcom-wl

Так что... любой можно использовать, главное чтобы понять какой лучше работает, на том и остановиться.

Первый у меня и стоял, теперь поставил 2-й. И в системе теперь оба. Главное чтобы они не начали конфликтовать.
Или надо один из них удалить, но какой?

[euspectre]

Полный вывод dmesg на момент, когда были проблемы с WiFi, тоже выложите куда-нибудь, если нетрудно.
Хочется разобраться и сделать так, чтобы проблемы с пропаданием WiFi после обновлений в будущем не проявлялись.

Насчёт драйверов. Тех, что теоретически могут работать с Вашим WiFi-адаптером, на самом деле, 3:
- brcmsmac и b43 поставляются вместе с ядром и система обычно сама выбирает нужный,
- wl (проприетарный драйвер, пакет dkms-broadcom-wl) можно установить отдельно, что Вы и сделали. OK. Он иногда работает лучше указанных выше драйверов. Это нужно на конкретной системе смотреть.

Для того, чтобы b43 работал нормально, нужен ещё пакет b43-firmware-install, он у Вас установлен, OK.

Конфликтов между этими драйверами в наших системах быть не должно. Если же всё-таки будут - исправим.

Удалять пока ничего не надо.

[Галахов Роман]

Полный вывод dmesg на момент, когда были проблемы с WiFi, тоже выложите куда-нибудь, если нетрудно.
Хочется разобраться и сделать так, чтобы проблемы с пропаданием WiFi после обновлений в будущем не проявлялись.

Насчёт драйверов. Тех, что теоретически могут работать с Вашим WiFi-адаптером, на самом деле, 3:
- brcmsmac и b43 поставляются вместе с ядром и система обычно сама выбирает нужный,
- wl (проприетарный драйвер, пакет dkms-broadcom-wl) можно установить отдельно, что Вы и сделали. OK. Он иногда работает лучше указанных выше драйверов. Это нужно на конкретной системе смотреть.

Для того, чтобы b43 работал нормально, нужен ещё пакет b43-firmware-install, он у Вас установлен, OK.

Конфликтов между этими драйверами в наших системах быть не должно. Если же всё-таки будут - исправим.

Удалять пока ничего не надо.

Я думал, что вы хотели указать на то же, что и akdengi. Тогда полный вывод не делал. После установки dkms-broadcom-wl Wi-Fi восстановился.
Сейчас удалил dkms-broadcom-wl - Wi-Fi снова не виден.
Даю dmesg на текущее время (без dkms-broadcom-wl - Wi-Fi не виден). Возможно, что-то сломано в драйверах из ядра.

Код: Выделить всё

Travelmate roman # dmesg
[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Initializing cgroup subsys cpuacct
[    0.000000] Linux version 3.10.9-nrj-desktop-1rosa (mockbuild@localhost) (gcc version 4.7.3 20121001 (ROSA) (Linaro GCC 4.7-2012.10) ) #1 SMP PREEMPT Tue Aug 27 19:36:40 MSK 2013
[    0.000000] Command line: BOOT_IMAGE=/boot/vmlinuz-3.10.9-nrj-desktop-1rosa root=UUID=1dda5550-f4f4-4104-bbdd-80ca83154355 ro splash=silent logo.nologo quiet resume=/dev/sda5 init=/lib/systemd/systemd
[    0.000000] e820: BIOS-provided physical RAM map:
[    0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009cfff] usable
[    0.000000] BIOS-e820: [mem 0x000000000009d000-0x000000000009ffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000000e0000-0x00000000000fffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000000100000-0x00000000b363efff] usable
[    0.000000] BIOS-e820: [mem 0x00000000b363f000-0x00000000b36befff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000b36bf000-0x00000000b37befff] ACPI NVS
[    0.000000] BIOS-e820: [mem 0x00000000b37bf000-0x00000000b37fefff] ACPI data
[    0.000000] BIOS-e820: [mem 0x00000000b37ff000-0x00000000b37fffff] usable
[    0.000000] BIOS-e820: [mem 0x00000000b3800000-0x00000000bfffffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000e0000000-0x00000000efffffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000feb00000-0x00000000feb03fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000fec00fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fed10000-0x00000000fed13fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fed18000-0x00000000fed19fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fed1b000-0x00000000fed1ffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fee00000-0x00000000fee00fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000ffe00000-0x00000000ffffffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000100000000-0x0000000137ffffff] usable
[    0.000000] NX (Execute Disable) protection: active
[    0.000000] SMBIOS 2.6 present.
[    0.000000] DMI: Acer TravelMate 8372/TravelMate 8372, BIOS V1.07 12/14/2010
[    0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[    0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[    0.000000] No AGP bridge found
[    0.000000] e820: last_pfn = 0x138000 max_arch_pfn = 0x400000000
[    0.000000] MTRR default type: uncachable
[    0.000000] MTRR fixed ranges enabled:
[    0.000000]   00000-9FFFF write-back
[    0.000000]   A0000-BFFFF uncachable
[    0.000000]   C0000-EFFFF write-through
[    0.000000]   F0000-FFFFF write-combining
[    0.000000] MTRR variable ranges enabled:
[    0.000000]   0 base 000000000 mask F80000000 write-back
[    0.000000]   1 base 0FFE00000 mask FFFE00000 write-protect
[    0.000000]   2 base 080000000 mask FC0000000 write-back
[    0.000000]   3 base 0B8000000 mask FF8000000 uncachable
[    0.000000]   4 base 0B4000000 mask FFC000000 uncachable
[    0.000000]   5 base 0B3800000 mask FFF800000 uncachable
[    0.000000]   6 base 100000000 mask FC0000000 write-back
[    0.000000]   7 base 138000000 mask FF8000000 uncachable
[    0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[    0.000000] e820: last_pfn = 0xb3800 max_arch_pfn = 0x400000000
[    0.000000] Base memory trampoline at [ffff880000097000] 97000 size 24576
[    0.000000] init_memory_mapping: [mem 0x00000000-0x000fffff]
[    0.000000]  [mem 0x00000000-0x000fffff] page 4k
[    0.000000] BRK [0x01eec000, 0x01eecfff] PGTABLE
[    0.000000] BRK [0x01eed000, 0x01eedfff] PGTABLE
[    0.000000] BRK [0x01eee000, 0x01eeefff] PGTABLE
[    0.000000] init_memory_mapping: [mem 0x137e00000-0x137ffffff]
[    0.000000]  [mem 0x137e00000-0x137ffffff] page 2M
[    0.000000] BRK [0x01eef000, 0x01eeffff] PGTABLE
[    0.000000] init_memory_mapping: [mem 0x134000000-0x137dfffff]
[    0.000000]  [mem 0x134000000-0x137dfffff] page 2M
[    0.000000] init_memory_mapping: [mem 0x100000000-0x133ffffff]
[    0.000000]  [mem 0x100000000-0x133ffffff] page 2M
[    0.000000] init_memory_mapping: [mem 0x00100000-0xb363efff]
[    0.000000]  [mem 0x00100000-0x001fffff] page 4k
[    0.000000]  [mem 0x00200000-0xb35fffff] page 2M
[    0.000000]  [mem 0xb3600000-0xb363efff] page 4k
[    0.000000] init_memory_mapping: [mem 0xb37ff000-0xb37fffff]
[    0.000000]  [mem 0xb37ff000-0xb37fffff] page 4k
[    0.000000] RAMDISK: [mem 0x3776e000-0x37baefff]
[    0.000000] ACPI: RSDP 00000000000fe020 00024 (v02 ACRSYS)
[    0.000000] ACPI: XSDT 00000000b37fe120 00074 (v01 ACRSYS ACRPRDCT 00000001      01000013)
[    0.000000] ACPI: FACP 00000000b37fc000 000F4 (v04 ACRSYS ACRPRDCT 00000001 1025 01000013)
[    0.000000] ACPI: DSDT 00000000b37ec000 0C969 (v02 ACRSYS ACRPRDCT 00000001 1025 01000013)
[    0.000000] ACPI: FACS 00000000b375e000 00040
[    0.000000] ACPI: ASF! 00000000b37fd000 000A5 (v32 ACRSYS ACRPRDCT 00000001 1025 01000013)
[    0.000000] ACPI: HPET 00000000b37fb000 00038 (v01 ACRSYS ACRPRDCT 00000001 1025 01000013)
[    0.000000] ACPI: APIC 00000000b37fa000 0008C (v02 ACRSYS ACRPRDCT 00000001 1025 01000013)
[    0.000000] ACPI: MCFG 00000000b37f9000 0003C (v01 ACRSYS ACRPRDCT 00000001 1025 01000013)
[    0.000000] ACPI: SLIC 00000000b37eb000 00176 (v01 ACRSYS ACRPRDCT 00000001 1025 01000013)
[    0.000000] ACPI: BOOT 00000000b37e7000 00028 (v01 ACRSYS ACRPRDCT 00000001 1025 01000013)
[    0.000000] ACPI: ASPT 00000000b37e4000 00034 (v04 ACRSYS ACRPRDCT 00000001 1025 01000013)
[    0.000000] ACPI: WDAT 00000000b37e3000 00224 (v01 ACRSYS ACRPRDCT 00000001 1025 01000013)
[    0.000000] ACPI: SSDT 00000000b37e2000 009F1 (v01  PmRef    CpuPm 00003000 INTL 20051117)
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] No NUMA configuration found
[    0.000000] Faking a node at [mem 0x0000000000000000-0x0000000137ffffff]
[    0.000000] Initmem setup node 0 [mem 0x00000000-0x137ffffff]
[    0.000000]   NODE_DATA [mem 0x137ff9000-0x137ffcfff]
[    0.000000]  [ffffea0000000000-ffffea0004dfffff] PMD -> [ffff880133a00000-ffff8801375fffff] on node 0
[    0.000000] Zone ranges:
[    0.000000]   DMA      [mem 0x00001000-0x00ffffff]
[    0.000000]   DMA32    [mem 0x01000000-0xffffffff]
[    0.000000]   Normal   [mem 0x100000000-0x137ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00001000-0x0009cfff]
[    0.000000]   node   0: [mem 0x00100000-0xb363efff]
[    0.000000]   node   0: [mem 0xb37ff000-0xb37fffff]
[    0.000000]   node   0: [mem 0x100000000-0x137ffffff]
[    0.000000] On node 0 totalpages: 964060
[    0.000000]   DMA zone: 64 pages used for memmap
[    0.000000]   DMA zone: 21 pages reserved
[    0.000000]   DMA zone: 3996 pages, LIFO batch:0
[    0.000000]   DMA32 zone: 11417 pages used for memmap
[    0.000000]   DMA32 zone: 730688 pages, LIFO batch:31
[    0.000000]   Normal zone: 3584 pages used for memmap
[    0.000000]   Normal zone: 229376 pages, LIFO batch:31
[    0.000000] ACPI: PM-Timer IO Port: 0x408
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x04] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x05] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x05] lapic_id[0x00] disabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x06] lapic_id[0x00] disabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x07] lapic_id[0x00] disabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x08] lapic_id[0x00] disabled)
[    0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[    0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[    0.000000] ACPI: IRQ0 used by override.
[    0.000000] ACPI: IRQ2 used by override.
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[    0.000000] smpboot: Allowing 8 CPUs, 4 hotplug CPUs
[    0.000000] nr_irqs_gsi: 40
[    0.000000] PM: Registered nosave memory: 000000000009d000 - 00000000000a0000
[    0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000
[    0.000000] PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
[    0.000000] PM: Registered nosave memory: 00000000b363f000 - 00000000b36bf000
[    0.000000] PM: Registered nosave memory: 00000000b36bf000 - 00000000b37bf000
[    0.000000] PM: Registered nosave memory: 00000000b37bf000 - 00000000b37ff000
[    0.000000] PM: Registered nosave memory: 00000000b3800000 - 00000000c0000000
[    0.000000] PM: Registered nosave memory: 00000000c0000000 - 00000000e0000000
[    0.000000] PM: Registered nosave memory: 00000000e0000000 - 00000000f0000000
[    0.000000] PM: Registered nosave memory: 00000000f0000000 - 00000000feb00000
[    0.000000] PM: Registered nosave memory: 00000000feb00000 - 00000000feb04000
[    0.000000] PM: Registered nosave memory: 00000000feb04000 - 00000000fec00000
[    0.000000] PM: Registered nosave memory: 00000000fec00000 - 00000000fec01000
[    0.000000] PM: Registered nosave memory: 00000000fec01000 - 00000000fed10000
[    0.000000] PM: Registered nosave memory: 00000000fed10000 - 00000000fed14000
[    0.000000] PM: Registered nosave memory: 00000000fed14000 - 00000000fed18000
[    0.000000] PM: Registered nosave memory: 00000000fed18000 - 00000000fed1a000
[    0.000000] PM: Registered nosave memory: 00000000fed1a000 - 00000000fed1b000
[    0.000000] PM: Registered nosave memory: 00000000fed1b000 - 00000000fed20000
[    0.000000] PM: Registered nosave memory: 00000000fed20000 - 00000000fee00000
[    0.000000] PM: Registered nosave memory: 00000000fee00000 - 00000000fee01000
[    0.000000] PM: Registered nosave memory: 00000000fee01000 - 00000000ffe00000
[    0.000000] PM: Registered nosave memory: 00000000ffe00000 - 0000000100000000
[    0.000000] e820: [mem 0xc0000000-0xdfffffff] available for PCI devices
[    0.000000] Booting paravirtualized kernel on bare hardware
[    0.000000] setup_percpu: NR_CPUS:64 nr_cpumask_bits:64 nr_cpu_ids:8 nr_node_ids:1
[    0.000000] PERCPU: Embedded 28 pages/cpu @ffff880137c00000 s85440 r8192 d21056 u262144
[    0.000000] pcpu-alloc: s85440 r8192 d21056 u262144 alloc=1*2097152
[    0.000000] pcpu-alloc: [0] 0 1 2 3 4 5 6 7 
[    0.000000] Built 1 zonelists in Node order, mobility grouping on.  Total pages: 948974
[    0.000000] Policy zone: Normal
[    0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-3.10.9-nrj-desktop-1rosa root=UUID=1dda5550-f4f4-4104-bbdd-80ca83154355 ro splash=silent logo.nologo quiet resume=/dev/sda5 init=/lib/systemd/systemd
[    0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[    0.000000] Checking aperture...
[    0.000000] No AGP bridge found
[    0.000000] Calgary: detecting Calgary via BIOS EBDA area
[    0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
[    0.000000] Memory: 3707832k/5111808k available (6319k kernel code, 1255568k absent, 148408k reserved, 6811k data, 1208k init)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000]  Dump stacks of tasks blocking RCU-preempt GP.
[    0.000000]  RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=8.
[    0.000000] NR_IRQS:4352 nr_irqs:744 16
[    0.000000] Console: colour dummy device 80x25
[    0.000000] console [tty0] enabled
[    0.000000] hpet clockevent registered
[    0.000000] tsc: Fast TSC calibration using PIT
[    0.001000] tsc: Detected 2666.844 MHz processor
[    0.000003] Calibrating delay loop (skipped), value calculated using timer frequency.. 5333.68 BogoMIPS (lpj=2666844)
[    0.000005] pid_max: default: 32768 minimum: 301
[    0.000026] Security Framework initialized
[    0.000035] TOMOYO Linux initialized
[    0.000261] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
[    0.001177] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
[    0.001600] Mount-cache hash table entries: 256
[    0.001781] Initializing cgroup subsys devices
[    0.001784] Initializing cgroup subsys freezer
[    0.001785] Initializing cgroup subsys net_cls
[    0.001787] Initializing cgroup subsys blkio
[    0.001788] Initializing cgroup subsys bfqio
[    0.001809] CPU: Physical Processor ID: 0
[    0.001810] CPU: Processor Core ID: 0
[    0.001815] mce: CPU supports 9 MCE banks
[    0.001823] CPU0: Thermal monitoring handled by SMI
[    0.001832] Last level iTLB entries: 4KB 512, 2MB 7, 4MB 7
Last level dTLB entries: 4KB 512, 2MB 32, 4MB 32
tlb_flushall_shift: 6
[    0.001932] Freeing SMP alternatives: 20k freed
[    0.002814] ACPI: Core revision 20130328
[    0.010887] ACPI: All ACPI Tables successfully acquired
[    0.032424] ftrace: allocating 22975 entries in 90 pages
[    0.043419] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[    0.053428] smpboot: CPU0: Intel(R) Core(TM) i5 CPU       M 480  @ 2.67GHz (fam: 06, model: 25, stepping: 05)
[    0.155363] Performance Events: PEBS fmt1+, 16-deep LBR, Westmere events, Intel PMU driver.
[    0.155370] perf_event_intel: CPUID marked event: 'bus cycles' unavailable
[    0.155373] ... version:                3
[    0.155374] ... bit width:              48
[    0.155374] ... generic registers:      4
[    0.155375] ... value mask:             0000ffffffffffff
[    0.155376] ... max period:             000000007fffffff
[    0.155377] ... fixed-purpose events:   3
[    0.155378] ... event mask:             000000070000000f
[    0.175472] CPU1: Thermal monitoring handled by SMI
[    0.190578] CPU2: Thermal monitoring handled by SMI
[    0.205591] CPU3: Thermal monitoring handled by SMI
[    0.164431] smpboot: Booting Node   0, Processors  #1 #2 #3
[    0.207708] Brought up 4 CPUs
[    0.207713] smpboot: Total of 4 processors activated (21334.75 BogoMIPS)
[    0.210166] devtmpfs: initialized
[    0.211053] PM: Registering ACPI NVS region [mem 0xb36bf000-0xb37befff] (1048576 bytes)
[    0.211882] xor: measuring software checksum speed
[    0.221352]    prefetch64-sse: 12084.000 MB/sec
[    0.231351]    generic_sse: 10660.000 MB/sec
[    0.231352] xor: using function: prefetch64-sse (12084.000 MB/sec)
[    0.231377] RTC time: 18:29:10, date: 11/13/13
[    0.231414] NET: Registered protocol family 16
[    0.231517] ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
[    0.231519] ACPI: bus type PCI registered
[    0.231578] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
[    0.231581] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in E820
[    0.244951] PCI: Using configuration type 1 for base access
[    0.245479] bio: create slab <bio-0> at 0
[    0.262359] raid6: sse2x1    7101 MB/s
[    0.279350] raid6: sse2x2    8328 MB/s
[    0.296355] raid6: sse2x4    9246 MB/s
[    0.296356] raid6: using algorithm sse2x4 (9246 MB/s)
[    0.296357] raid6: using ssse3x2 recovery algorithm
[    0.296403] ACPI: Added _OSI(Module Device)
[    0.296405] ACPI: Added _OSI(Processor Device)
[    0.296406] ACPI: Added _OSI(3.0 _SCP Extensions)
[    0.296408] ACPI: Added _OSI(Processor Aggregator Device)
[    0.297969] ACPI: EC: Look up EC in DSDT
[    0.299443] ACPI: Executed 1 blocks of module-level executable AML code
[    0.306728] [Firmware Bug]: ACPI: BIOS _OSI(Linux) query ignored
[    0.307098] ACPI: SSDT 00000000b3691598 00530 (v01  PmRef  Cpu0Ist 00003000 INTL 20051117)
[    0.307472] ACPI: Dynamic OEM Table Load:
[    0.307474] ACPI: SSDT           (null) 00530 (v01  PmRef  Cpu0Ist 00003000 INTL 20051117)
[    0.307608] ACPI: SSDT 00000000b368f018 00891 (v01  PmRef  Cpu0Cst 00003001 INTL 20051117)
[    0.307961] ACPI: Dynamic OEM Table Load:
[    0.307962] ACPI: SSDT           (null) 00891 (v01  PmRef  Cpu0Cst 00003001 INTL 20051117)
[    0.312884] ACPI: SSDT 00000000b3690a98 00303 (v01  PmRef    ApIst 00003000 INTL 20051117)
[    0.313287] ACPI: Dynamic OEM Table Load:
[    0.313289] ACPI: SSDT           (null) 00303 (v01  PmRef    ApIst 00003000 INTL 20051117)
[    0.315522] ACPI: SSDT 00000000b368ed98 00119 (v01  PmRef    ApCst 00003000 INTL 20051117)
[    0.315903] ACPI: Dynamic OEM Table Load:
[    0.315905] ACPI: SSDT           (null) 00119 (v01  PmRef    ApCst 00003000 INTL 20051117)
[    0.319303] ACPI: Interpreter enabled
[    0.319310] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S1_] (20130328/hwxface-568)
[    0.319316] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S2_] (20130328/hwxface-568)
[    0.319334] ACPI: (supports S0 S3 S4 S5)
[    0.319335] ACPI: Using IOAPIC for interrupt routing
[    0.319368] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[    0.319478] ACPI: No dock devices found.
[    0.678386] ACPI: Power Resource [FN00] (off)
[    0.678458] ACPI: Power Resource [FN01] (off)
[    0.679146] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-fe])
[    0.679177] \_SB_.PCI0:_OSC invalid UUID
[    0.679178] _OSC request data:1 8 0 
[    0.679663] PCI host bridge to bus 0000:00
[    0.679666] pci_bus 0000:00: root bus resource [bus 00-fe]
[    0.679668] pci_bus 0000:00: root bus resource [io  0x0000-0x0cf7]
[    0.679669] pci_bus 0000:00: root bus resource [io  0x0d00-0xffff]
[    0.679671] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff]
[    0.679672] pci_bus 0000:00: root bus resource [mem 0xc0000000-0xfeafffff]
[    0.679680] pci 0000:00:00.0: [8086:0044] type 00 class 0x060000
[    0.679697] DMAR: BIOS has allocated no shadow GTT; disabling IOMMU for graphics
[    0.679763] pci 0000:00:02.0: [8086:0046] type 00 class 0x030000
[    0.679773] pci 0000:00:02.0: reg 10: [mem 0xd0000000-0xd03fffff 64bit]
[    0.679779] pci 0000:00:02.0: reg 18: [mem 0xc0000000-0xcfffffff 64bit pref]
[    0.679783] pci 0000:00:02.0: reg 20: [io  0x4050-0x4057]
[    0.679861] pci 0000:00:16.0: [8086:3b64] type 00 class 0x078000
[    0.679889] pci 0000:00:16.0: reg 10: [mem 0xd6406100-0xd640610f 64bit]
[    0.679986] pci 0000:00:16.0: PME# supported from D0 D3hot D3cold
[    0.680072] pci 0000:00:1a.0: [8086:3b3c] type 00 class 0x0c0320
[    0.680610] pci 0000:00:1a.0: reg 10: [mem 0xd6405c00-0xd6405fff]
[    0.683807] pci 0000:00:1a.0: PME# supported from D0 D3hot D3cold
[    0.683869] pci 0000:00:1b.0: [8086:3b56] type 00 class 0x040300
[    0.683890] pci 0000:00:1b.0: reg 10: [mem 0xd6400000-0xd6403fff 64bit]
[    0.683984] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[    0.684020] pci 0000:00:1b.0: System wakeup disabled by ACPI
[    0.684050] pci 0000:00:1c.0: [8086:3b42] type 01 class 0x060400
[    0.684149] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[    0.684187] pci 0000:00:1c.0: System wakeup disabled by ACPI
[    0.684216] pci 0000:00:1c.1: [8086:3b44] type 01 class 0x060400
[    0.684313] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
[    0.684355] pci 0000:00:1c.1: System wakeup disabled by ACPI
[    0.684384] pci 0000:00:1c.2: [8086:3b46] type 01 class 0x060400
[    0.684481] pci 0000:00:1c.2: PME# supported from D0 D3hot D3cold
[    0.684519] pci 0000:00:1c.2: System wakeup disabled by ACPI
[    0.684559] pci 0000:00:1d.0: [8086:3b34] type 00 class 0x0c0320
[    0.685103] pci 0000:00:1d.0: reg 10: [mem 0xd6405800-0xd6405bff]
[    0.688342] pci 0000:00:1d.0: PME# supported from D0 D3hot D3cold
[    0.688380] pci 0000:00:1d.0: System wakeup disabled by ACPI
[    0.688411] pci 0000:00:1e.0: [8086:2448] type 01 class 0x060401
[    0.688491] pci 0000:00:1e.0: System wakeup disabled by ACPI
[    0.688520] pci 0000:00:1f.0: [8086:3b09] type 00 class 0x060100
[    0.688667] pci 0000:00:1f.2: [8086:3b29] type 00 class 0x010601
[    0.688694] pci 0000:00:1f.2: reg 10: [io  0x4048-0x404f]
[    0.688704] pci 0000:00:1f.2: reg 14: [io  0x405c-0x405f]
[    0.688715] pci 0000:00:1f.2: reg 18: [io  0x4040-0x4047]
[    0.688725] pci 0000:00:1f.2: reg 1c: [io  0x4058-0x405b]
[    0.688736] pci 0000:00:1f.2: reg 20: [io  0x4020-0x403f]
[    0.688746] pci 0000:00:1f.2: reg 24: [mem 0xd6405000-0xd64057ff]
[    0.688811] pci 0000:00:1f.2: PME# supported from D3hot
[    0.688882] pci 0000:00:1f.3: [8086:3b30] type 00 class 0x0c0500
[    0.688902] pci 0000:00:1f.3: reg 10: [mem 0xd6406000-0xd64060ff 64bit]
[    0.688931] pci 0000:00:1f.3: reg 20: [io  0x4000-0x401f]
[    0.689022] pci 0000:00:1f.6: [8086:3b32] type 00 class 0x118000
[    0.689049] pci 0000:00:1f.6: reg 10: [mem 0xd6404000-0xd6404fff 64bit]
[    0.689316] pci 0000:01:00.0: [14e4:4357] type 00 class 0x028000
[    0.689363] pci 0000:01:00.0: reg 10: [mem 0xd5400000-0xd5403fff 64bit]
[    0.689587] pci 0000:01:00.0: supports D1 D2
[    0.689588] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
[    0.689639] pci 0000:01:00.0: System wakeup disabled by ACPI
[    0.691398] pci 0000:00:1c.0: PCI bridge to [bus 01]
[    0.691406] pci 0000:00:1c.0:   bridge window [io  0x3000-0x3fff]
[    0.691413] pci 0000:00:1c.0:   bridge window [mem 0xd5400000-0xd63fffff]
[    0.691424] pci 0000:00:1c.0:   bridge window [mem 0xd0400000-0xd13fffff 64bit pref]
[    0.691502] pci 0000:00:1c.1: PCI bridge to [bus 02]
[    0.691507] pci 0000:00:1c.1:   bridge window [io  0x2000-0x2fff]
[    0.691511] pci 0000:00:1c.1:   bridge window [mem 0xd4400000-0xd53fffff]
[    0.691518] pci 0000:00:1c.1:   bridge window [mem 0xd1400000-0xd23fffff 64bit pref]
[    0.691648] pci 0000:03:00.0: [14e4:1690] type 00 class 0x020000
[    0.691690] pci 0000:03:00.0: reg 10: [mem 0xd3400000-0xd340ffff 64bit]
[    0.691921] pci 0000:03:00.0: PME# supported from D3hot D3cold
[    0.691978] pci 0000:03:00.0: System wakeup disabled by ACPI
[    0.693393] pci 0000:00:1c.2: PCI bridge to [bus 03]
[    0.693401] pci 0000:00:1c.2:   bridge window [io  0x1000-0x1fff]
[    0.693408] pci 0000:00:1c.2:   bridge window [mem 0xd3400000-0xd43fffff]
[    0.693418] pci 0000:00:1c.2:   bridge window [mem 0xd2400000-0xd33fffff 64bit pref]
[    0.693517] pci 0000:00:1e.0: PCI bridge to [bus 04] (subtractive decode)
[    0.693530] pci 0000:00:1e.0:   bridge window [io  0x0000-0x0cf7] (subtractive decode)
[    0.693531] pci 0000:00:1e.0:   bridge window [io  0x0d00-0xffff] (subtractive decode)
[    0.693533] pci 0000:00:1e.0:   bridge window [mem 0x000a0000-0x000bffff] (subtractive decode)
[    0.693534] pci 0000:00:1e.0:   bridge window [mem 0xc0000000-0xfeafffff] (subtractive decode)
[    0.693592] \_SB_.PCI0:_OSC invalid UUID
[    0.693593] _OSC request data:1 1f 0 
[    0.693596] acpi PNP0A08:00: ACPI _OSC support notification failed, disabling PCIe ASPM
[    0.693598] acpi PNP0A08:00: Unable to request _OSC control (_OSC support mask: 0x08)
[    0.694196] ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 *7 10 12 14 15)
[    0.694242] ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 11 12 14 15) *10
[    0.694287] ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
[    0.694335] ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 11 12 14 15) *10
[    0.694381] ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 7 10 12 14 15) *0, disabled.
[    0.694425] ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 7 *11 12 14 15)
[    0.694469] ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
[    0.694514] ACPI: PCI Interrupt Link [LNKH] (IRQs 1 3 4 5 6 *7 11 12 14 15)
[    0.694614] ACPI: PCI Root Bridge [CPBG] (domain 0000 [bus ff])
[    0.694659] PCI host bridge to bus 0000:ff
[    0.694661] pci_bus 0000:ff: root bus resource [bus ff]
[    0.694666] pci 0000:ff:00.0: [8086:2c62] type 00 class 0x060000
[    0.694699] pci 0000:ff:00.1: [8086:2d01] type 00 class 0x060000
[    0.694734] pci 0000:ff:02.0: [8086:2d10] type 00 class 0x060000
[    0.694764] pci 0000:ff:02.1: [8086:2d11] type 00 class 0x060000
[    0.694794] pci 0000:ff:02.2: [8086:2d12] type 00 class 0x060000
[    0.694823] pci 0000:ff:02.3: [8086:2d13] type 00 class 0x060000
[    0.694862] acpi PNP0A03:00: ACPI _OSC support notification failed, disabling PCIe ASPM
[    0.694863] acpi PNP0A03:00: Unable to request _OSC control (_OSC support mask: 0x08)
[    0.695135] ACPI: Enabled 4 GPEs in block 00 to 3F
[    0.695140] acpi root: \_SB_.PCI0 notify handler is installed
[    0.695185] acpi root: \_SB_.CPBG notify handler is installed
[    0.695197] Found 2 acpi root devices
[    0.695223] ACPI: EC: GPE = 0x17, I/O: command/status = 0x66, data = 0x62
[    0.695344] vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
[    0.695347] vgaarb: loaded
[    0.695348] vgaarb: bridge control possible 0000:00:02.0
[    0.695402] SCSI subsystem initialized
[    0.695404] ACPI: bus type ATA registered
[    0.695436] libata version 3.00 loaded.
[    0.695513] PCI: Using ACPI for IRQ routing
[    0.705280] PCI: pci_cache_line_size set to 64 bytes
[    0.705398] e820: reserve RAM buffer [mem 0x0009d000-0x0009ffff]
[    0.705399] e820: reserve RAM buffer [mem 0xb363f000-0xb3ffffff]
[    0.705401] e820: reserve RAM buffer [mem 0xb3800000-0xb3ffffff]
[    0.705476] NetLabel: Initializing
[    0.705478] NetLabel:  domain hash size = 128
[    0.705478] NetLabel:  protocols = UNLABELED CIPSOv4
[    0.705487] NetLabel:  unlabeled traffic allowed by default
[    0.705525] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0, 0, 0, 0, 0
[    0.705529] hpet0: 8 comparators, 64-bit 14.318180 MHz counter
[    0.707546] Switching to clocksource hpet
[    0.713625] pnp: PnP ACPI init
[    0.713635] ACPI: bus type PNP registered
[    0.714018] pnp 00:00: [dma 4]
[    0.714045] pnp 00:00: Plug and Play ACPI device, IDs PNP0200 (active)
[    0.714062] pnp 00:01: Plug and Play ACPI device, IDs INT0800 (active)
[    0.714173] pnp 00:02: Plug and Play ACPI device, IDs PNP0103 (active)
[    0.714227] pnp 00:03: Plug and Play ACPI device, IDs PNP0c04 (active)
[    0.714254] pnp 00:04: disabling [io  0x164e-0x164f] because it overlaps 0000:00:1c.2 BAR 13 [io  0x1000-0x1fff]
[    0.714284] system 00:04: [io  0x0680-0x069f] has been reserved
[    0.714286] system 00:04: [io  0x0800-0x080f] has been reserved
[    0.714287] system 00:04: [io  0x0810-0x0813] has been reserved
[    0.714289] system 00:04: [io  0xffff] has been reserved
[    0.714291] system 00:04: [io  0x0400-0x047f] has been reserved
[    0.714292] system 00:04: [io  0x0500-0x057f] has been reserved
[    0.714295] system 00:04: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.714316] pnp 00:05: Plug and Play ACPI device, IDs PNP0b00 (active)
[    0.714337] pnp 00:06: Plug and Play ACPI device, IDs PNP0303 (active)
[    0.714360] pnp 00:07: Plug and Play ACPI device, IDs SYN1b41 SYN1b00 SYN0002 PNP0f13 (active)
[    0.714655] system 00:08: [mem 0xfed1c000-0xfed1ffff] has been reserved
[    0.714657] system 00:08: [mem 0xfed10000-0xfed13fff] has been reserved
[    0.714659] system 00:08: [mem 0xfed18000-0xfed18fff] has been reserved
[    0.714660] system 00:08: [mem 0xfed19000-0xfed19fff] has been reserved
[    0.714662] system 00:08: [mem 0xe0000000-0xefffffff] has been reserved
[    0.714664] system 00:08: [mem 0xfed20000-0xfed3ffff] has been reserved
[    0.714666] system 00:08: [mem 0xff000000-0xffffffff] could not be reserved
[    0.714667] system 00:08: [mem 0xfee00000-0xfeefffff] could not be reserved
[    0.714669] system 00:08: [mem 0xd6500000-0xd6500fff] has been reserved
[    0.714671] system 00:08: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.714787] pnp: PnP ACPI: found 9 devices
[    0.714788] ACPI: bus type PNP unregistered
[    0.719377] pci 0000:00:1c.0: PCI bridge to [bus 01]
[    0.719381] pci 0000:00:1c.0:   bridge window [io  0x3000-0x3fff]
[    0.719387] pci 0000:00:1c.0:   bridge window [mem 0xd5400000-0xd63fffff]
[    0.719392] pci 0000:00:1c.0:   bridge window [mem 0xd0400000-0xd13fffff 64bit pref]
[    0.719399] pci 0000:00:1c.1: PCI bridge to [bus 02]
[    0.719402] pci 0000:00:1c.1:   bridge window [io  0x2000-0x2fff]
[    0.719408] pci 0000:00:1c.1:   bridge window [mem 0xd4400000-0xd53fffff]
[    0.719412] pci 0000:00:1c.1:   bridge window [mem 0xd1400000-0xd23fffff 64bit pref]
[    0.719419] pci 0000:00:1c.2: PCI bridge to [bus 03]
[    0.719422] pci 0000:00:1c.2:   bridge window [io  0x1000-0x1fff]
[    0.719428] pci 0000:00:1c.2:   bridge window [mem 0xd3400000-0xd43fffff]
[    0.719432] pci 0000:00:1c.2:   bridge window [mem 0xd2400000-0xd33fffff 64bit pref]
[    0.719440] pci 0000:00:1e.0: PCI bridge to [bus 04]
[    0.719693] pci 0000:00:1e.0: setting latency timer to 64
[    0.719698] pci_bus 0000:00: resource 4 [io  0x0000-0x0cf7]
[    0.719700] pci_bus 0000:00: resource 5 [io  0x0d00-0xffff]
[    0.719701] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
[    0.719703] pci_bus 0000:00: resource 7 [mem 0xc0000000-0xfeafffff]
[    0.719705] pci_bus 0000:01: resource 0 [io  0x3000-0x3fff]
[    0.719706] pci_bus 0000:01: resource 1 [mem 0xd5400000-0xd63fffff]
[    0.719708] pci_bus 0000:01: resource 2 [mem 0xd0400000-0xd13fffff 64bit pref]
[    0.719709] pci_bus 0000:02: resource 0 [io  0x2000-0x2fff]
[    0.719711] pci_bus 0000:02: resource 1 [mem 0xd4400000-0xd53fffff]
[    0.719712] pci_bus 0000:02: resource 2 [mem 0xd1400000-0xd23fffff 64bit pref]
[    0.719714] pci_bus 0000:03: resource 0 [io  0x1000-0x1fff]
[    0.719715] pci_bus 0000:03: resource 1 [mem 0xd3400000-0xd43fffff]
[    0.719716] pci_bus 0000:03: resource 2 [mem 0xd2400000-0xd33fffff 64bit pref]
[    0.719718] pci_bus 0000:04: resource 4 [io  0x0000-0x0cf7]
[    0.719720] pci_bus 0000:04: resource 5 [io  0x0d00-0xffff]
[    0.719721] pci_bus 0000:04: resource 6 [mem 0x000a0000-0x000bffff]
[    0.719723] pci_bus 0000:04: resource 7 [mem 0xc0000000-0xfeafffff]
[    0.719756] NET: Registered protocol family 2
[    0.719921] TCP established hash table entries: 32768 (order: 7, 524288 bytes)
[    0.720054] TCP bind hash table entries: 32768 (order: 7, 524288 bytes)
[    0.720161] TCP: Hash tables configured (established 32768 bind 32768)
[    0.720190] TCP: reno registered
[    0.720196] UDP hash table entries: 2048 (order: 4, 65536 bytes)
[    0.720214] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
[    0.720279] NET: Registered protocol family 1
[    0.720291] pci 0000:00:02.0: Boot video device
[    0.742796] PCI: CLS 64 bytes, default 64
[    0.742848] Trying to unpack rootfs image as initramfs...
[    1.180784] Freeing initrd memory: 4356k freed
[    1.181686] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[    1.181692] software IO TLB [mem 0xaf63f000-0xb363f000] (64MB) mapped at [ffff8800af63f000-ffff8800b363efff]
[    1.181729] Simple Boot Flag at 0x44 set to 0x1
[    1.182043] audit: initializing netlink socket (disabled)
[    1.182056] type=2000 audit(1384367350.699:1): initialized
[    1.200304] bounce pool size: 64 pages
[    1.200313] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[    1.201391] VFS: Disk quotas dquot_6.5.2
[    1.201425] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    1.201769] bio: create slab <bio-1> at 1
[    1.201883] Btrfs loaded
[    1.201889] msgmni has been set to 7250
[    1.202182] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[    1.202219] io scheduler noop registered
[    1.202220] io scheduler deadline registered
[    1.202241] io scheduler cfq registered
[    1.202259] io scheduler bfq registered (default)
[    1.202515] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    1.202946] Linux agpgart interface v0.103
[    1.202996] agpgart-intel 0000:00:00.0: Intel HD Graphics Chipset
[    1.203039] agpgart-intel 0000:00:00.0: detected gtt size: 2097152K total, 262144K mappable
[    1.203680] agpgart-intel 0000:00:00.0: detected 131072K stolen memory
[    1.203819] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xc0000000
[    1.203895] vesafb: mode is 1024x768x32, linelength=4096, pages=0
[    1.203896] vesafb: scrolling: redraw
[    1.203898] vesafb: Truecolor: size=8:8:8:8, shift=24:16:8:0
[    1.204078] vesafb: framebuffer at 0xc0000000, mapped to 0xffffc90010b80000, using 3072k, total 3072k
[    1.317727] Console: switching to colour frame buffer device 128x48
[    1.431308] fb0: VESA VGA frame buffer device
[    1.431318] intel_idle: MWAIT substates: 0x1120
[    1.431319] intel_idle: v0.4 model 0x25
[    1.431321] intel_idle: lapic_timer_reliable_states 0xffffffff
[    1.431408] GHES: HEST is not enabled!
[    1.432438] brd: module loaded
[    1.432636] mei_me 0000:00:16.0: setting latency timer to 64
[    1.432672] mei_me 0000:00:16.0: irq 40 for MSI/MSI-X
[    1.434966] ahci 0000:00:1f.2: version 3.0
[    1.435068] ahci 0000:00:1f.2: irq 41 for MSI/MSI-X
[    1.435134] ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 4 ports 3 Gbps 0x3 impl SATA mode
[    1.435137] ahci 0000:00:1f.2: flags: 64bit ncq sntf ilck pm led clo pio slum part ems apst 
[    1.435142] ahci 0000:00:1f.2: setting latency timer to 64
[    1.436789] scsi0 : ahci
[    1.436855] scsi1 : ahci
[    1.436909] scsi2 : ahci
[    1.436961] scsi3 : ahci
[    1.436987] ata1: SATA max UDMA/133 abar m2048@0xd6405000 port 0xd6405100 irq 41
[    1.436990] ata2: SATA max UDMA/133 abar m2048@0xd6405000 port 0xd6405180 irq 41
[    1.436991] ata3: DUMMY
[    1.436992] ata4: DUMMY
[    1.437054] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[    1.441292] i8042: Detected active multiplexing controller, rev 1.1
[    1.443631] serio: i8042 KBD port at 0x60,0x64 irq 1
[    1.443652] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[    1.443664] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[    1.443676] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[    1.443688] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[    1.443760] mousedev: PS/2 mouse device common for all mice
[    1.443868] rtc_cmos 00:05: RTC can wake from S4
[    1.443987] rtc_cmos 00:05: rtc core: registered rtc_cmos as rtc0
[    1.444018] rtc_cmos 00:05: alarms up to one year, y3k, 242 bytes nvram, hpet irqs
[    1.444076] cpuidle: using governor ladder
[    1.444146] cpuidle: using governor menu
[    1.444150] ledtrig-cpu: registered to indicate activity on CPUs
[    1.444199] scsi4 : vhba
[    1.444338] TCP: cubic registered
[    1.444348] Key type dns_resolver registered
[    1.444537] PM: Checking hibernation image partition /dev/sda5
[    1.483697] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
[    1.741709] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[    1.741816] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[    1.742384] ata1.00: ATA-7: INTEL SSDSA2M160G2GC, 2CV102J6, max UDMA/133
[    1.742387] ata1.00: 312581808 sectors, multi 1: LBA48 NCQ (depth 31/32)
[    1.742852] ata1.00: configured for UDMA/133
[    1.743175] scsi 0:0:0:0: Direct-Access     ATA      INTEL SSDSA2M160 2CV1 PQ: 0 ANSI: 5
[    1.743468] sd 0:0:0:0: [sda] 312581808 512-byte logical blocks: (160 GB/149 GiB)
[    1.743951] sd 0:0:0:0: [sda] Write Protect is off
[    1.743956] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    1.744069] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    1.745625]  sda: sda1 sda2 < sda5 sda6 sda7 >
[    1.745839] ata2.00: ATAPI: HL-DT-ST DVDRAM GU10N, AP04, max UDMA/133
[    1.746058] sd 0:0:0:0: [sda] Attached SCSI disk
[    1.750746] ata2.00: configured for UDMA/133
[    1.756359] scsi 1:0:0:0: CD-ROM            HL-DT-ST DVDRAM GU10N     AP04 PQ: 0 ANSI: 5
[    2.184828] tsc: Refined TSC clocksource calibration: 2666.760 MHz
[    2.184831] Switching to clocksource tsc
[    2.486525] psmouse serio4: synaptics: Touchpad model: 1, fw: 7.2, id: 0x1c0b1, caps: 0xd04733/0xa40000/0xa0000, board id: 3655, fw id: 549736
[    2.524343] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio4/input/input1
[    2.526897] PM: Hibernation image partition 8:5 present
[    2.526902] PM: Looking for hibernation image.
[    2.527224] PM: Image not found (code -22)
[    2.527228] PM: Hibernation image not present or could not be loaded.
[    2.527257] registered taskstats version 1
[    2.528122]   Magic number: 5:842:493
[    2.528264] rtc_cmos 00:05: setting system clock to 2013-11-13 18:29:12 UTC (1384367352)
[    2.528268] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[    2.528270] EDD information not available.
[    2.530383] Freeing unused kernel memory: 1208k freed
[    2.530681] Write protecting the kernel read-only data: 12288k
[    2.535453] Freeing unused kernel memory: 1864k freed
[    2.537870] Freeing unused kernel memory: 1180k freed
[    2.565993] dracut: dracut-Free 2012.1 Desktop dracut-027-
[    2.587904] systemd-udevd[133]: starting version 194
[    2.608901] [drm] Initialized drm 1.1.0 20060810
[    2.609822] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input2
[    2.609830] ACPI: Power Button [PWRB]
[    2.609881] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input3
[    2.709795] ACPI: Lid Switch [LID0]
[    2.709903] input: Sleep Button as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input4
[    2.709912] ACPI: Sleep Button [SLPB]
[    2.710013] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input5
[    2.710020] ACPI: Power Button [PWRF]
[    2.716598] [drm] Memory usable by graphics device = 2048M
[    2.716602] checking generic (c0000000 300000) vs hw (c0000000 10000000)
[    2.716604] fb: conflicting fb hw usage inteldrmfb vs VESA VGA - removing generic driver
[    2.716621] Console: switching to colour dummy device 80x25
[    2.716706] i915 0000:00:02.0: setting latency timer to 64
[    2.752485] i915 0000:00:02.0: irq 42 for MSI/MSI-X
[    2.752505] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[    2.752508] [drm] Driver supports precise vblank timestamp query.
[    2.752652] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem
[    2.788272] fbcon: inteldrmfb (fb0) is primary device
[    3.714774] Console: switching to colour frame buffer device 170x48
[    3.720339] i915 0000:00:02.0: fb0: inteldrmfb frame buffer device
[    3.720343] i915 0000:00:02.0: registered panic notifier
[    3.722443] acpi device:02: registered as cooling_device0
[    3.722711] ACPI: Video Device [GFX0] (multi-head: yes  rom: no  post: no)
[    3.722791] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/LNXVIDEO:00/input/input6
[    3.722847] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
[    3.726280] dracut: Starting plymouth daemon
[    4.908981] ACPI: bus type USB registered
[    4.909004] usbcore: registered new interface driver usbfs
[    4.909011] usbcore: registered new interface driver hub
[    4.909054] usbcore: registered new device driver usb
[    4.909340] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    4.909472] ehci-pci: EHCI PCI platform driver
[    4.909626] ehci-pci 0000:00:1a.0: setting latency timer to 64
[    4.909638] ehci-pci 0000:00:1a.0: EHCI Host Controller
[    4.909642] ehci-pci 0000:00:1a.0: new USB bus registered, assigned bus number 1
[    4.909658] ehci-pci 0000:00:1a.0: debug port 2
[    4.913611] ehci-pci 0000:00:1a.0: cache line size of 64 is not supported
[    4.913634] ehci-pci 0000:00:1a.0: irq 16, io mem 0xd6405c00
[    4.918790] ehci-pci 0000:00:1a.0: USB 2.0 started, EHCI 1.00
[    4.918823] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    4.918825] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    4.918828] usb usb1: Product: EHCI Host Controller
[    4.918830] usb usb1: Manufacturer: Linux 3.10.9-nrj-desktop-1rosa ehci_hcd
[    4.918832] usb usb1: SerialNumber: 0000:00:1a.0
[    4.919033] hub 1-0:1.0: USB hub found
[    4.919040] hub 1-0:1.0: 3 ports detected
[    4.919383] ehci-pci 0000:00:1d.0: setting latency timer to 64
[    4.919392] ehci-pci 0000:00:1d.0: EHCI Host Controller
[    4.919400] ehci-pci 0000:00:1d.0: new USB bus registered, assigned bus number 2
[    4.919416] ehci-pci 0000:00:1d.0: debug port 2
[    4.923378] ehci-pci 0000:00:1d.0: cache line size of 64 is not supported
[    4.923405] ehci-pci 0000:00:1d.0: irq 23, io mem 0xd6405800
[    4.925042] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
[    4.925046] cdrom: Uniform CD-ROM driver Revision: 3.20
[    4.925283] sr 1:0:0:0: Attached scsi CD-ROM sr0
[    4.929822] ehci-pci 0000:00:1d.0: USB 2.0 started, EHCI 1.00
[    4.930763] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[    4.930767] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    4.930769] usb usb2: Product: EHCI Host Controller
[    4.930771] usb usb2: Manufacturer: Linux 3.10.9-nrj-desktop-1rosa ehci_hcd
[    4.930773] usb usb2: SerialNumber: 0000:00:1d.0
[    4.930906] hub 2-0:1.0: USB hub found
[    4.930913] hub 2-0:1.0: 3 ports detected
[    5.220855] usb 1-1: new high-speed USB device number 2 using ehci-pci
[    5.335423] usb 1-1: New USB device found, idVendor=8087, idProduct=0020
[    5.335428] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[    5.336032] hub 1-1:1.0: USB hub found
[    5.336219] hub 1-1:1.0: 6 ports detected
[    5.423860] PM: Marking nosave pages: [mem 0x0009d000-0x000fffff]
[    5.423865] PM: Marking nosave pages: [mem 0xb363f000-0xb37fefff]
[    5.423872] PM: Marking nosave pages: [mem 0xb3800000-0xffffffff]
[    5.424609] PM: Basic memory bitmaps created
[    5.437200] PM: Basic memory bitmaps freed
[    5.437207] video LNXVIDEO:00: Restoring backlight state
[    5.438746] usb 2-1: new high-speed USB device number 2 using ehci-pci
[    5.439902] PM: Starting manual resume from disk
[    5.439907] PM: Hibernation image partition 8:5 present
[    5.439909] PM: Looking for hibernation image.
[    5.440878] PM: Image not found (code -22)
[    5.440880] PM: Hibernation image not present or could not be loaded.
[    5.477499] EXT4-fs (sda6): mounted filesystem with ordered data mode. Opts: (null)
[    5.495096] dracut: Checking ext4: /dev/disk/by-uuid/1dda5550-f4f4-4104-bbdd-80ca83154355
[    5.495167] dracut: issuing e2fsck -a  /dev/disk/by-uuid/1dda5550-f4f4-4104-bbdd-80ca83154355
[    5.513031] dracut: /dev/disk/by-uuid/1dda5550-f4f4-4104-bbdd-80ca83154355: clean, 467687/2662400 files, 6784805/10636651 blocks
[    5.514239] dracut: Mounting /dev/disk/by-uuid/1dda5550-f4f4-4104-bbdd-80ca83154355 with -o defaults,ro
[    5.519792] EXT4-fs (sda6): mounted filesystem with ordered data mode. Opts: (null)
[    5.553245] usb 2-1: New USB device found, idVendor=8087, idProduct=0020
[    5.553251] usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[    5.553480] hub 2-1:1.0: USB hub found
[    5.553578] hub 2-1:1.0: 8 ports detected
[    5.559352] dracut: Mounted root filesystem /dev/sda6
[    5.627848] usb 1-1.2: new high-speed USB device number 3 using ehci-pci
[    5.629909] dracut: Switching root
[    5.674450] systemd[1]: RTC configured in localtime, applying delta of 240 minutes to system time.
[    5.678468] systemd[1]: systemd 194 running in system mode. (+PAM +LIBWRAP +AUDIT -SELINUX +IMA +SYSVINIT +LIBCRYPTSETUP +GCRYPT +ACL +XZ; mandriva)
[    5.696221] systemd[1]: Inserted module 'autofs4'
[    5.716409] NET: Registered protocol family 10
[    5.716590] systemd[1]: Inserted module 'ipv6'
[    5.718075] systemd[1]: Set hostname to <Travelmate.kenetic>.
[    5.738814] usb 1-1.2: New USB device found, idVendor=064e, idProduct=a219
[    5.738821] usb 1-1.2: New USB device strings: Mfr=2, Product=1, SerialNumber=3
[    5.738825] usb 1-1.2: Product: 1.3M WebCam
[    5.738828] usb 1-1.2: Manufacturer: Suyin
[    5.738832] usb 1-1.2: SerialNumber: HF1315-S32B-OV01-VA-R02.01.05
[    5.816850] usb 1-1.4: new full-speed USB device number 4 using ehci-pci
[    5.817459] systemd[1]: [/lib/systemd/system/fancontrol.service:3] Unknown lvalue 'ConditionFileNotEmpty' in section 'Unit'. Ignoring.
[    5.856446] systemd[1]: Starting RPC Port Mapper.
[    5.856588] systemd[1]: Reached target RPC Port Mapper.
[    5.856613] systemd[1]: Starting Forward Password Requests to Wall Directory Watch.
[    5.856727] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[    5.856769] systemd[1]: Starting Syslog Socket.
[    5.856930] systemd[1]: Listening on Syslog Socket.
[    5.856955] systemd[1]: Starting /dev/initctl Compatibility Named Pipe.
[    5.857079] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
[    5.857097] systemd[1]: Starting Delayed Shutdown Socket.
[    5.857222] systemd[1]: Listening on Delayed Shutdown Socket.
[    5.857242] systemd[1]: Starting Encrypted Volumes.
[    5.857342] systemd[1]: Reached target Encrypted Volumes.
[    5.857388] systemd[1]: Starting Arbitrary Executable File Formats File System Automount Point.
[    5.857621] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[    5.857644] systemd[1]: Expecting device dev-disk-by\x2duuid-91548cbe\x2d8008\x2d4083\x2da3b4\x2d62e0e0fee1d2.device...
[    5.857786] systemd[1]: Starting udev Kernel Socket.
[    5.857837] systemd[1]: Listening on udev Kernel Socket.
[    5.857880] systemd[1]: Starting udev Control Socket.
[    5.857935] systemd[1]: Listening on udev Control Socket.
[    5.857946] systemd[1]: Expecting device dev-sda7.device...
[    5.857977] systemd[1]: Starting Journal Socket.
[    5.858037] systemd[1]: Listening on Journal Socket.
[    5.858052] systemd[1]: Starting Syslog.
[    5.858088] systemd[1]: Reached target Syslog.
[    5.859716] systemd[1]: Starting Load legacy module configuration...
[    5.860313] systemd[1]: Started File System Check on Root Device.
[    5.860331] systemd[1]: Starting Remount Root and Kernel File Systems...
[    5.860683] systemd[1]: Starting Configure read-only root support...
[    5.861096] systemd[1]: Starting udev Coldplug all Devices...
[    5.861476] systemd[1]: Mounting Huge Pages File System...
[    5.863829] systemd[1]: Starting Load Kernel Modules...
[    5.864612] systemd[1]: Starting Journal Service...
[    5.865427] systemd[1]: Started Journal Service.
[    5.865648] systemd[1]: Mounting Debug File System...
[    5.866005] systemd[1]: Starting Setup Virtual Console...
[    5.866650] systemd[1]: Starting Set default kernel console loglevel...
[    5.867555] systemd[1]: Starting udev Kernel Device Manager...
[    5.867937] systemd[1]: Mounting POSIX Message Queue File System...
[    5.868727] systemd[1]: Starting Apply Kernel Variables...
[    5.870982] systemd[1]: Started Set Up Additional Binary Formats.
[    5.903517] usb 1-1.4: New USB device found, idVendor=1c7a, idProduct=0801
[    5.903524] usb 1-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    5.903528] usb 1-1.4: Product: FingerPrinter Reader
[    5.903532] usb 1-1.4: Manufacturer: Generic
[    5.903535] usb 1-1.4: SerialNumber: 00000000000006
[    5.966889] usb 2-1.2: new low-speed USB device number 3 using ehci-pci
[    6.055388] usb 2-1.2: New USB device found, idVendor=15d9, idProduct=0a4f
[    6.055396] usb 2-1.2: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[    6.055401] usb 2-1.2: Product:  USB OPTICAL MOUSE
[    6.079298] systemd-udevd[313]: starting version 194
[    6.095360] systemd-udevd[313]: specified group 'scanner' unknown
[    6.170662] EXT4-fs (sda6): re-mounted. Opts: (null)
[    6.339387] microcode: CPU0 sig=0x20655, pf=0x10, revision=0x2
[    6.453092] microcode: CPU0 sig=0x20655, pf=0x10, revision=0x2
[    6.453300] microcode: CPU0 updated to revision 0x4, date = 2013-06-28
[    6.453312] microcode: CPU1 sig=0x20655, pf=0x10, revision=0x2
[    6.453338] microcode: CPU1 sig=0x20655, pf=0x10, revision=0x2
[    6.453508] microcode: CPU1 updated to revision 0x4, date = 2013-06-28
[    6.453517] microcode: CPU2 sig=0x20655, pf=0x10, revision=0x2
[    6.453541] microcode: CPU2 sig=0x20655, pf=0x10, revision=0x2
[    6.453711] microcode: CPU2 updated to revision 0x4, date = 2013-06-28
[    6.453719] microcode: CPU3 sig=0x20655, pf=0x10, revision=0x2
[    6.453741] microcode: CPU3 sig=0x20655, pf=0x10, revision=0x2
[    6.453913] microcode: CPU3 updated to revision 0x4, date = 2013-06-28
[    6.454400] microcode: Microcode Update Driver: v2.00 <tigran@aivazian.fsnet.co.uk>, Peter Oruba
[    6.534699] snd_hda_intel 0000:00:1b.0: irq 43 for MSI/MSI-X
[    6.581131] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input7
[    6.632262] ACPI Warning: 0x0000000000004000-0x000000000000401f SystemIO conflicts with Region \_SB_.PCI0.SBUS.SMBI 1 (20130328/utaddress-251)
[    6.632272] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[    6.710089] bcma: bus0: Found chip with id 0xA8D9, rev 0x01 and package 0x0A
[    6.710129] bcma: bus0: Core 0 found: ChipCommon (manuf 0x4BF, id 0x800, rev 0x22, class 0x0)
[    6.710162] bcma: bus0: Core 1 found: IEEE 802.11 (manuf 0x4BF, id 0x812, rev 0x17, class 0x0)
[    6.710225] bcma: bus0: Core 2 found: PCIe (manuf 0x4BF, id 0x820, rev 0x0F, class 0x0)
[    6.725158] bcma: bus0: Bus registered
[    6.754175] ACPI: Requesting acpi_cpufreq
[    6.756339] ACPI Warning: 0x0000000000000428-0x000000000000042f SystemIO conflicts with Region \PMIO 1 (20130328/utaddress-251)
[    6.756348] ACPI Warning: 0x0000000000000428-0x000000000000042f SystemIO conflicts with Region \PMBA 2 (20130328/utaddress-251)
[    6.756353] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[    6.756357] ACPI Warning: 0x0000000000000540-0x000000000000054f SystemIO conflicts with Region \GPIO 1 (20130328/utaddress-251)
[    6.756361] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[    6.756363] ACPI Warning: 0x0000000000000530-0x000000000000053f SystemIO conflicts with Region \GPIO 1 (20130328/utaddress-251)
[    6.756367] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[    6.756369] ACPI Warning: 0x0000000000000500-0x000000000000052f SystemIO conflicts with Region \GPIO 1 (20130328/utaddress-251)
[    6.756373] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[    6.756375] lpc_ich: Resource conflict(s) found affecting gpio_ich
[    6.785271] pps_core: LinuxPPS API ver. 1 registered
[    6.785276] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    6.787067] PTP clock support registered
[    6.896322] tg3.c:v3.132 (May 21, 2013)
[    6.901201] intel ips 0000:00:1f.6: CPU TDP doesn't match expected value (found 25, expected 29)
[    6.902186] wmi: Mapper loaded
[    6.902928] intel ips 0000:00:1f.6: IPS driver initialized, MCP temp limit 90
[    6.979432] ACPI: Fan [FAN0] (off)
[    6.979480] ACPI: Fan [FAN1] (off)
[    6.983476] kvm: VM_EXIT_LOAD_IA32_PERF_GLOBAL_CTRL does not work properly. Using workaround
[    7.003543] thermal LNXTHERM:00: registered as thermal_zone0
[    7.003549] ACPI: Thermal Zone [TZ00] (7 C)
[    7.003830] thermal LNXTHERM:01: registered as thermal_zone1
[    7.003833] ACPI: Thermal Zone [TZ01] (6 C)
[    7.027669] libphy: tg3 mdio bus: probed
[    7.180878] iTCO_vendor_support: vendor-support=0
[    7.182004] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.10
[    7.182051] iTCO_wdt: Found a HM55 TCO device (Version=2, TCOBASE=0x0460)
[    7.182186] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=1)
[    7.207954] acer_wmi: Acer Laptop ACPI-WMI Extras
[    7.207972] acer_wmi: Function bitmap for Communication Button: 0x801
[    7.207976] acer_wmi: Brightness must be controlled by acpi video driver
[    7.208693] input: Acer WMI hotkeys as /devices/virtual/input/input8
[    7.209010] input: Acer BMA150 accelerometer as /devices/virtual/input/input9
[    7.460108] ACPI: EC: GPE storm detected(9 GPEs), transactions will use polling mode
[    7.477975] tg3 0000:03:00.0 eth0: Tigon3 [partno(BCM957760) rev 57780001] (PCI Express) MAC address 00:1e:33:29:29:e5
[    7.477983] tg3 0000:03:00.0 eth0: attached PHY driver [Broadcom BCM57780] (mii_bus:phy_addr=300:01)
[    7.477985] tg3 0000:03:00.0 eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[1]
[    7.477988] tg3 0000:03:00.0 eth0: dma_rwctrl[76180000] dma_mask[64-bit]
[    7.498307] cfg80211: Calling CRDA to update world regulatory domain
[    7.600894] cfg80211: World regulatory domain updated:
[    7.600898] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[    7.600899] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[    7.600901] cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[    7.600902] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[    7.600903] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[    7.600904] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[    7.607445] hidraw: raw HID events driver (C) Jiri Kosina
[    7.613491] usbcore: registered new interface driver usbhid
[    7.613496] usbhid: USB HID core driver
[    7.649642] b43-phy0: Broadcom 43225 WLAN found (core revision 23)
[    7.650380] b43-phy0: Found PHY: Analog 8, Type 4 (N), Revision 6
[    7.650396] b43-phy0 debug: Found Radio: Manuf 0x17F, Version 0x2056, Revision 11
[    7.650925] Broadcom 43xx driver loaded [ Features: PMNLS ]
[    7.654511] b43-phy0 ERROR: Firmware file "b43/ucode16_mimo.fw" not found
[    7.654516] b43-phy0 ERROR: Firmware file "b43-open/ucode16_mimo.fw" not found
[    7.654519] b43-phy0 ERROR: You must go to http://wireless.kernel.org/en/users/Drivers/b43#devicefirmware and download the correct firmware for this driver version. Please carefully read all instructions on this website.
[    7.681944] ACPI: Battery Slot [BAT0] (battery present)
[    7.689890] ACPI: AC Adapter [ADP1] (off-line)
[    7.771612] input:  USB OPTICAL MOUSE as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.2/2-1.2:1.0/input/input10
[    7.773888] hid-generic 0003:15D9:0A4F.0001: input,hidraw0: USB HID v1.11 Mouse [ USB OPTICAL MOUSE] on usb-0000:00:1d.0-1.2/input0
[    7.966637] EXT4-fs (sda7): mounted filesystem with ordered data mode. Opts: (null)
[    7.998640] media: Linux media interface: v0.10
[    8.005304] Linux video capture interface: v2.00
[    8.016021] uvcvideo: Found UVC 1.00 device 1.3M WebCam (064e:a219)
[    8.025866] input: 1.3M WebCam as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.2/1-1.2:1.0/input/input11
[    8.025958] usbcore: registered new interface driver uvcvideo
[    8.025960] USB Video Class driver (1.1.1)
[    8.037057] Adding 9363948k swap on /dev/sda5.  Priority:-1 extents:1 across:9363948k SSFS
[    8.077642] device-mapper: uevent: version 1.0.3
[    8.077736] device-mapper: ioctl: 4.24.0-ioctl (2013-01-15) initialised: dm-devel@redhat.com
[    8.617833] systemd-journald[308]: Received SIGUSR1
[    9.613477] vboxdrv: Found 4 processor cores.
[    9.617746] vboxdrv: fAsync=0 offMin=0x2fb offMax=0x1c00
[    9.617836] vboxdrv: TSC mode is 'synchronous', kernel timer mode is 'normal'.
[    9.617838] vboxdrv: Successfully loaded version 4.2.18_OSE (interface 0x001a0005).
[   11.776161] EXT4-fs (sda6): re-mounted. Opts: data=ordered,commit=600
[   11.838714] EXT4-fs (sda7): re-mounted. Opts: data=ordered,commit=600
[   11.896459] tg3 0000:03:00.0: irq 44 for MSI/MSI-X
[   12.655545] tg3 0000:03:00.0 eth0: Link is down
[   12.656621] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   13.854363] Bluetooth: Core ver 2.16
[   13.854388] NET: Registered protocol family 31
[   13.854390] Bluetooth: HCI device and connection manager initialized
[   13.854401] Bluetooth: HCI socket layer initialized
[   13.854404] Bluetooth: L2CAP socket layer initialized
[   13.854409] Bluetooth: SCO socket layer initialized
[   14.035209] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[   14.035213] Bluetooth: BNEP filters: protocol multicast
[   14.035225] Bluetooth: BNEP socket layer initialized
[   45.580121] tun: Universal TUN/TAP device driver, 1.6
[   45.580126] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[   50.427487] fuse init (API version 7.22)
[   54.455742] ehci-pci 0000:00:1d.0: setting latency timer to 64
[   54.594834] usb 2-1.2: USB disconnect, device number 3
[   56.426822] usb 2-1.2: new low-speed USB device number 4 using ehci-pci
[   56.505577] usb 2-1.2: New USB device found, idVendor=15d9, idProduct=0a4f
[   56.505585] usb 2-1.2: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[   56.505590] usb 2-1.2: Product:  USB OPTICAL MOUSE
[   56.508184] input:  USB OPTICAL MOUSE as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.2/2-1.2:1.0/input/input12
[   56.508427] hid-generic 0003:15D9:0A4F.0002: input,hidraw0: USB HID v1.11 Mouse [ USB OPTICAL MOUSE] on usb-0000:00:1d.0-1.2/input0
[   64.168080] tg3 0000:03:00.0: irq 44 for MSI/MSI-X
[   64.927180] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
Travelmate roman # 

[euspectre]

Судя по логу, драйвер b43 не нашёл необх. файлы (firmware).

Попробуйте установить пакет b43-firmware и перезагрузить систему.
Можно вместо этого и пакет b43-firmware-install переустановить (вдруг недоустановился почему-то), но, как правило, надёжнее просто поставить b43-firmware.

Если после перезагрузки сеть не заработает, тогда опять выложите сюда вывод dmesg, пожалуйста.

[Галахов Роман]

b43-firmware был не установлен, b43-firmware-install переустановил, но он не потянул по зависимостям b43-firmware. Доустановил b43-firmware.
Сейчас удалю dkms-broadcom-wl - перезагружусь, проверю.

[Галахов Роман]

Wi-Fi увидел, но зависает на "Настройка интерфейса" 3 минуты ждал подключения нет. Даю вывод, но он очень большой получился. Даже "Code" не справился. Прилагаю в приложенном файле.

[Галахов Роман]

Доустановил dkms-broadcom-wl - Wi-Fi заработал.

[akdengi]

Иногда NM бывает "зависает" на управлении Wi-Fi - лечится убиранием и установкой галочки управления Wi-Fi в апплете или настройках. Похоже совпало.

[Галахов Роман]

Иногда NM бывает "зависает" на управлении Wi-Fi - лечится убиранием и установкой галочки управления Wi-Fi в апплете или настройках. Похоже совпало.

Если было бы так, я бы сюда не писал бы - это первое что я сразу проверил. Но

Wi-Fi увидел, но зависает на "Настройка интерфейса" 3 минуты ждал подключения нет.

на драйверах b43-firmware-install + b43-firmware - проверить думаю стоит.

[euspectre]

Да, пока лучше будет использовать dkms-broadcom-wl.

Что до лога, тут пока неясно. Система пытается подконнектиться, но получает отказ от точки доступа, похоже. И так раз за разом. Вряд ли это из-за NetworkManager'a, скорее, драйвер b43 не всё поддерживает, что нужно для работы с этим железом и точкой доступа в том режиме, как всё сейчас настроено.

Если с драйвером wl будут какие-то проблемы, можно будет убрать его и попробовать brcmsmac. На нём, IIRC, всё на этой системе и работало до тех обновлений.